Cisco, GOOSE, IEC61850, POWER BI, ABB IED, REx615, ABB 800xA, SIEMENS, Allen&Bradley, network monitoring, Optimisation, Vlan segregation

Aveva OMI, schneider m580 plc, sql database, danfoss vsd

Planning of works for electrical and control industrial systems; Troubleshooting of DCS issues for safe and fail-free operation; Developing and implementation of automated control systems. Installation and comissioning; Adaptation of software for operation needs; Adding and editing of algorithms for DCS, PLC; Programming new PLCs. Tuning, troubleshooting and testing of PLC and DCS before implementation; Failure analysing, imrpoving the quality and validity of PLC and DCS logic algorythms; Providing technical assistance to other departments in part of understanding the DCS; Management regarding all company and safety policies; Periodic inspections of fail-safe PLC, DCS operation. Schematic drawing mapping; Preparing instructions for operation staff; i. Successfully managed the control systems equipment and auxiliary systems, commissioned improvement projects and managed to consistently reduce the annual DCS related downtime to less than an hour - 1x 28 MW ABB GMDs - 2 X 22 MW ABB GMDs - 1 x 7MW ABB PINION DRIVEN MILL - 1 x 4MW Dual Drive Ball Mills Integrated the standalone Mill control systems onto the main plant DCS ABB System 800x A and implemented the Grinding circuits Expert using Metso OCS 4D Advanced Process Control. ii. Successfully implemented the Mine-to-Mill optimization system 4 domains, Regulatory Control, Protection Control, Stabilization Control and Optimization control throughout the whole mine value chain; 1. Drilling & Blasting - Estimation &evaluation of the operational level - Fragmentation analysis of the ROM material - D&B Optimization (PSD of plant feed) 2. Crushing& Screening - Ore characterization for crushing - Evaluation of equipment availability and utilization - Process performance evaluation of crushing and screening - Circuit Mass balancing, Modeling and Simulations 3. Milling Circuit - Ore characterization for milling - Process performance evaluation of milling and classification - Trajectory modeling for the liner profile over life of liner - Modeling , Simulation and calculation of recirculating load 4. Mine-to-Mill - Review, evaluation and optimization of overall performance (D&B+Crushing&Screening+Milling&Classification) - Evaluation and identifying opportunities to increase tph feed This has effectively helped in achieving 26.8MTPA from nameplate designs of 25MTPA with concentrator recoveries of 90% regardless of varying ore feed. iii. Successfully implemented the Froth Velocity cameras and Floatation Expert system using Metso OCS 4D Advanced Process Control system from Roughers to Final cleaners. Also implemented the Thickeners Bed Pressure Optimization for all sites.

Maintenance staff management. Selecting hardwire and spare parts for automaiton maintenance. Work with maintenance documentation;Oversaw the Installation and comissioning; Repairing, troubleshooting and maintenance of electronics parts and PLC at "Starlinger" PPE bags production automated line; Editing of PLC projects; Maintenance of Festo, Rexroth pneumatics; CCTV and fire alarm installation and maintenance. i. Reviewing and approving systems operating and diagnostic procedures (SOP) and Job Safety Analysis (JSA) in order to provide standardized guidelines for the DCS & APC team in maintaining and troubleshooting the instrumentation systems safely. ii. Planning, organizing, controlling, and evaluating DCS& APC maintenance activities, including installation and modification activities in order to meet availability target of equipment and high reliability of instrumentation system. iii. Offering expert advice on Process Control Strategies across. iv. Communicating, organizing, and controlling the implementation of company's safety and environmental policies and procedures, in order to ensure all subordinates perform their duties in a safe manner and environmentally conscious. v. Determining job priorities and assignments to subordinates, including planning and implementation of projects to ensure they are achieved on schedule. vi. Performing final quality check on repaired and/or maintained process equipment in order to ensure the entire system is functional and meets operational requirements. vii. Identifying and analyzing breakdown and directing subordinates on how to repair broken equipment, in order to ensure the root causes of the problem will be fixed appropriately, effectively and efficiently. viii. Directing, monitoring, and reviewing subordinate's performance and assisting them during their technical activities to minimize possibilities of rework and to ensure compliance with time and quality standards required. ix. Liaising with Process Control Equipment vendors internationally on all matters of Control. x. nstallation / Maintenance, Configuring of Field Bus Systems (Profibus / Ethernet) / Fibre Optical Systems, Siemens Scalance Networking Equipment – ensuring that both Company and Vendor Safety and Quality standards are adhered to, whilst ensuring minimum disruption to the Process Plant Operation or Production. xi. Performing Fault Analysis / Fault Finding of all breakdowns relating to the Process Control System (Software, Hardware and Equipment), Field Bus Systems (Profibus / Ethernet) / Fibre Optical Systems in order to eliminate re-occurrences of repetitive faults and improve Process Control System reliability and efficiency. xii. Perform Operational Optimization of the Process Control System in terms of Software Coding, Control Algorithms, PID Control Loop and other Complex Algorithms in conjunction with Operations, Technical and relevant Engineering Disciplines. xiii. Performing Process Control System Audits, Adequate Process Control Backups, Regular Functional Testing of the Process Control Back-Ups, Compliance with Licensing Protocols, Effective Control & Management of Process Control Spares, Budget Control and Cost Savings Initiatives. xiv. Executing Planned and Preventative Maintenance Schedules / Tasks and procedures that’s applicable to the Process Control System and initiate and review the Planned / Preventative Maintenance Tasks and Schedules xv. Adhering to the Management of Change Procedures (Plant Change Requests, Software Change Requests resulting from Plant Change Requests, Redlining of Process Control Documentation and Drawings - Systems / Network Drawings / Loop Drawings) in area of responsibility. xvi. Interacting with Senior Supervisors, Instrumentation Technicians and other Operational / Technical and Engineering disciplines in order to provide a full range of Control & Instrumentation Services / Support to Production, Processing Team, and other Engineering Teams.

Repairing, troubleshooting and maintenance of electronics parts and PLC at "Starlinger" PPE bags production automated line; Editing of PLC projects; Maintenance of Festo, Rexroth pneumatics; CCTV and fire alarm installation and maintenance.

Срочная служба

Maintenance and troubleshooting of automation and instrumentation devices; Schematic drawings mapping via Autocad;Tuning of PID controllers. Maintenance of TREI PLC and SCADA iFix 3.0. Was prepared for automation engineer position.

information and computer technology, bachelor of information and computer technology

Automatic information processing and control systems, Programmer

Automation and control, Instrumentation technician 4th category